Page History

Anchor
ObjectEvaluation ObjectEvaluation

Object evaluation

To prevent objects from appearing to be too similar or to reduce the risk, you can either increase the Entrance Threshold of the object if possible, or modify the marker positions.

For more information, see Understand object evaluation.

Calibrate selected camera

You can now calibrate or re-calbrate calibrate a single camera, without having spend time re-calibrating the whole system. This enables you to add a new camera to your system, or move a single calibrated camera, and calibrate with a shorter wand wave, saving the time it takes to perform a longer wand wave for all the cameras.

To calibrate a selected camera:

1. With the moved or additional camera positioned in the volume, in the System tree, select the relevant camera, which is flagged as Uncalibrated ( ) if it is a new camera, or Bumped () if it is a moved camera that was connected when it was moved.
   
   
   
   
2. On the Camera Calibration tab, in the Auto-Masking section, click the Cameras to Mask list and then click Selected Cameras.
3. Click Start (Selected).
   The camera masking is updated to include the new or moved camera.

4. In the System tree, ensure the relevant camera is still selected. 

   Scroll Pagebreak

5. In the Calibration Wave section:

   1. To ensure that only the wand wave for the selected camera is required to meet the Auto Stop Minimum Wands value, make sure Auto Stop is selected.
   2. Click Start (Selected).
      
      
      
      
6. In the volume, ensure that the person waving the wand does not stand too close to the new or moved camera, so that the wave can be captured by both the directly affected camera and the adjacent cameras.
   During calibration, the selected camera is at the top of the Wand Count list until its wave is completed, when the list returns to the usual (device number) order.
   Calibration takes noticeably less time than the original full system calibration.
   When calibration is complete, in the System tree, the relevant camera is flagged as connected and calibrated, with no other icons ().

System panel improvements

The System panel has been improved for 1.4, making it more responsive and providing more helpful feedback, especially for large systems.

System and device parameters have been  reorganized to make it easier to find the options you need.

System file settings are now available from the System Settings menu, to the right of the top menu bar, next to View Settings.

You can now remove disconnected or selected devices from the system (see Remove selected devices).

Most application configuration files are now stored in JSON format rather than XML. Configuration files created in Evoke 1.3.# or earlier are converted on import into Evoke 1.4.

New device status summary

Device category headers are now always visible, and include a summary of device status and warnings. This makes it easier to view the current status of the system and to identify any issues at a glance.

For Pulsars, this includes battery charge level and number of devices on charge.

High Speed mode for Vicon Vantage cameras

When upgraded to the latest firmware (Firmware 725 and later), Evoke 1.4 enables you to use High Speed mode with your Vantage cameras without having to change the field of view (FOV) or lens. When you capture optical data, subsampling (selectively reducing the pixel count) enables you to run at high camera frame rates without reducing the FOV (frame size). 

Previously, to run Vantage cameras at higher frame rates while maintaining their maximum resolution, windowing was used, which reduces the size of the FOV.

Now, in new High Speed mode, you can run your Vantage cameras at higher frames rates while maintaining the FOV. You can change frame rates during capture and you don't need to set up your cameras again when you increase the frame rate, as the FOV is unchanged.

Note that because the higher speeds are achieved through subsampling (removing some pixels from the frames), some reduction in resolution is incurred. For details, see High-speed mode in the Vicon Vantage Reference Guide.

To select high-speed mode:

1. At the top of the System panel, set the frame rate to the speed you want to use in High Speed mode.
   A warning may temporarily be displayed, alerting you to the discrepancy between the requested frame rate and the actual system frame rate, until you select high speed mode for all the relevant cameras, as explained next.
2. In the System tree, select one or more cameras. 

   Scroll Pagebreak

3. In the Properties pane below, ensure the Advanced properties are displayed and in the Optical Setup section, click the Sensor Mode list and select High Speed.
   
   
   
   In the Cameras view in the Workspace, notice that the High Speed mode icon is displayed to the right of the other information about the selected camera(s).
   
   
   
   After a few moments, the system runs at the new speed.

Anchor
RemoveSelected RemoveSelected

Remove selected devices

In Evoke 1.4, a new option enables you to remove selected missing cluster(s) from the list of devices on the System tab.

To remove unwanted devices:

1. On the System tab, right-click on the device(s) that you want to remove.
2. Point to Remove, and then click Selected.
   
   

Other updates

• Anchor
  EntranceThreshold EntranceThreshold

  Improved object recognition For more reliable object recognition, the Entrance Threshold has been increased to a default value of 1.0. This ensures that 100% of markers are needed to boot the object, but note that it may take longer to boot than the previous default of 0.00.

   The entrance threshold is set in two places:

  • The overall entrance threshold (Processing tab > Object Tracking section > Entrance Threshold setting) sets the default entrance threshold for all objects.
    
    
    
    Normally, we recommend that you leave this at its default setting. You can override this setting for individual objects by using an object preset, as described next. 

    Scroll Pagebreak

  • You can change the entrance threshold for a selected object by using an object preset.
    
    
    
    For more information, see Resolve issues with object similarity in Getting started with Vicon Evoke.

• Additional events added to the Log 
• Firmware update Evoke 1.4 includes the Pulsar Reprogramming Tool with firmware updated to 727. This update provides stability and connectivty improvements as well as addressing a number of issues.
• Snap to 90 enabled by default. To avoid having rotated camera views that don't fit in the camera view grid, Snap to 90° is now enabled by default.
  To change this, in the Cameras view, display View Filters and clear the relevant check box.
  
  

• The Processing panel now offers a search facility and other controls that determine the visibility of the component properties.